How to Flash MotoQ to tekcirC(reverse) with Wap & MMS.
This tutorial will show you how to flash your Motorola Q from start to finish with WAP & MMS.
Tools:
RSD General 4.9.8
Activesync 4.2
tekcirC PRL file
Phmregistry 0.7(include with)
Rapiconfig (include with)
Delete-n-set.xml file (include with the attachment) can not attach because forum rule only alow 14k this is 25k so the link is below to download
http://www.megaupload.com/?d=YJOT74OQ
Let the fun begin
Flashing:
Install activesync.
Make sure under Settings->Connections->USB to PC->”Enable advanced network functionality” on your phone is checked
Plug in your phone it will install driver and it connect with active sync (you don’t need to sync just connect as a guess will be fine)
Open RSD General 4.9.8
Click on “Phone Provisioning” on the Left
Put the check mark on “PRL” and “Mobile IP” but nothing else (the blue lettering on the left-hand side)
Click “Read Phone” button. Be patient and wait until it finish
Click on the “PRL” blue lettering on the left
Click on “Open File” button to choose the tekcirC PRL you want to flash
Click on “Mobile IP” blue lettering on the left
Under the drop down menu of “Mobile IP Behavior” choose “Simple IP Only” and don’t change anything in here, leave it alone.
** Now make sure you have a check mark on both the “PRL” and “Mobile IP” but nothing else, before you hit the “Write Phone” button
Click on “Write Phone” button
It going to pop-up and say “You are about to write Mobile IP and CDMA PRL” just click “OK”
Wait until it finish and you done the first part.
You might need to restart your phone because it got stuck on the D-mode. So turn off the phone and turn it back on. If it won’t turn off. Take out the battery.
Now the phone only capable of talk and text.
tekcirC Wap setting:
Download the attachment and unzip then put the unzipped folder named Q in your C: not to any folder just C: so it would be like this C:\Q
In the Q folder you will have3 file rapiconfig.exe, Command Prompt and delete-n-set.xml
Right click on the file delete-n-set.xml and open with notepad and replace where it said
5055505050@mycricket.com to your phone number @mycricket.com so 5055505050 will be replace with your own 10digits phone number. Click on file->save and close the notepad
Run the command Prompt and type after the “>” cd C:\Q
So it should be like this >cd C:\Q and press enter
Then it will jump down to the next line and it look like this C:\Q>
Now type this in >rapiconfig.exe /p delete-n-set.xml there is a space between exe and /p
It should look like this C:\Q>rapiconfig.exe /p delete-n-set.xml (now hit enter)
Now you will see it said
“Config results written to output file RapiconfigOut.xml.”
“Config succeeded.”
You are done with wap setting. Unplug the phone from your computer
You can turn off the phone and turn it back on. Go to internet explore on your phone and access the tekcirC web site
http://wap.cricket.motricity.com It should work if you have web on your tekcirC account.
MMS setting:
Load the phmregistry into your phone and installed (I don’t have to show you how to do this should I? No. I should leave it to you to figure it out because I don’t evern know how to install a .cab file to my phone.) Click ok when it said “ may not display properly because it designed for previous version”. And click done
After it done install on your phone. Go to Start and open PHM Registry Editor (on you phone)
Go to HKEY_LOCAL_MACHINE -> Software -> Motorola -> MMS -> Profiles
Now in Profiles you will see VZW MMS you can change this to CKT MMS by press Menu and choose Rename. Or you can leave it alone it would effect anything it just a name for the profile.
I assumed that you have change the VZW MMS to CKT MMS from this point on
Choose CKT MMS. In here won’t see anything yet.
Press “Values”. Now it will show you the following item
Data Connections
Gateway
IP Address
MMSC URL
Port
Profile Locked
Now choose “IP Address”. You notice the default address is “gw.vzwwap.com” change this to “10.3.0.41”. Make sure you hit “Done” to save the setting and then it will bring you back to the list above.
Choose “MMSC URL” and you will have
http://mms.vtext.com/servlets/mms as default. Change the word “vtext” to “mycricket” and click done to save.
Choose “Port” and make sure it “8080” and click done to save
Do not change anything else. You could if you sure you know what you are doing.
That it you are done click the “end” key to go to the main screen and restart your phone so it fresh .
Have fun and enjoy the motoQ on tekcirC. Now you don’t have to wait for tekcirC to release the Q if the rumor is true.